Flushing Procedure for Fixed Foam Pump Systems

1. Isolate the Foam Pump(KEXON) agent tank from the firefighting system. Follow appropriate instructions and/or manuals related to the specific system.

2. Relieve pressure from any pressure vessel through the shell vent valve on the top of the tank.

3. Completely drain the water from the shell of any bladder tank in accordance with appropriate procedures.

4. Transfer the foam agent to be replaced from the tank into suitable storage containers. Use a transfer pump where applicable. Refer to the manufacturer’s manual for specific draining procedures. Properly label temporary foam agent storage containers and dispose of the foam in accordance with local regulatory authority require-ments for chemical labelling and disposal.

5. Rinse the foam agent tank with clean, fresh water and drain. Open all tank fill, tank return, and drain lines while

rinsing to remove any accumulated surface residue and help prevent cross contamination. Be sure to collect and dispose of drained rinse water in accordance with applicable local regulations. Repeat this process with fresh water to ensure the internal tank surfaces are clear of any accumulated contaminants.

6. Close all valves to ensure the foam tank system is a closed circuit.

7. Fill the foam agent tank with clean, fresh water to a level that ensures all connecting pipework is flooded. For bladder tanks, be sure to use appropriate fill procedures so the bladder is not damaged.

Click Foam Pump Manufacturers to learn about more information

Superior Design Features and Benefits of The Foam Pumps

The Foam Pump(KEXON) is the first of seven models in a complete line of positive displacement rotary gear foam pumps. The foam pumps have been specifically design for the rugged firefighting industry with design features found nowhere else–designed for the 21st century. In firefighting, there are no second chances, so don’t rely on inferior or outdated designs, specify and buy the best–lives and property are depending upon your foam pump choice.

Timing gears are used to synchronize the two pumping rotors. This design provides no rotor-to-rotor contact allowing for run dry conditions without damage, pumping of foam concentrate or water – water can be used for calibration, testing, and training, in lieu of foam concentrate. Timing gears are lubricated in an oil bath splash system – no regular greasing maintenance is required.

Brass pump body and heads with bronze alloy rotors.17-4PH (Precipitation Hardening) stainless steel pump shafts. Shafts have the strength of 416 stainless steel and corrosion resistance of 316 stainless steel.Each pump shaft/rotor assembly is supported by two double row, spherical roller bearings, sealed for life – no regular greasing maintenance required.Each pump shaft/rotor assembly is sealed into the pump body using two silicon carbide mechanical seals. This design prevents foam concentrate contact with the pump shafts to prevent corrosion. No Leaky Lip Seals!

Click Foam Pump Suppliers to learn about more information

Foam Pump Manufacturers

Plastic is made from raw oil and gas that are turned into polymers and finally into the finished bottles using an injection molding process. A Foam Pump Manufacturers(KEXON) usually makes different kinds of Foam Pump bottles in various shapes and sizes. However, since plastic encompasses a vast range of different plastic materials, man plastic bottle manufacturer concentrate their expertise on a fixed range of bottles. All plastic bottle manufacturers do not make custom design bottles either.

Plastic bottles are used for a variety of purposes ranging from pharmaceutical products, to household, to kitchen, to industrial and more. So your product may need a small bottle containing a few ml of liquid or a large bottle that can hold upwards of a liter. You may require food grade virgin plastic or regular plastic or even recycled plastic. Different plastic bottles include Round, Oval with E-Z grip, Rectangular, Cylindrical, Straight sided, Boston round, Oblong, Wide mouthed, Graduated, Decanter.

Most of these bottles can be used with varying kinds of closures ranging from screw on ones to sprays or pumps or flip tops. The kind of bottle you require depends on the type of product that you want to put in it, including its consistency. You may want readymade plastic bottles or want to get custom designed ones, transparent or opaque. As bottles are available in a huge range of sizes, shapes and materials, and you may want plastic bottles in varying sizes as well for the same product, you may require some guidance as to which kind of plastic bottle manufacturer is right for you and your product.

Click Foam Pump to learn about more information

The Principle of A Good Foam Pump

The Foam Pump(KEXON), also known as the push-type foam pump, is a liquid dispenser that uses the principle of atmospheric balance to pump out the liquid in the bottle and fill the outside atmosphere into the bottle. The main performance indicators of the foam pump: air pressure times, pumping volume, downforce, head opening torque, rebound speed, water intake indicators. Also known as a push-type foam pump, it is a liquid dispenser that uses the principle of atmospheric balance to pump out the liquid in the bottle and fill the outside atmosphere into the bottle. The main performance indicators of the foam pump: air pressure times, pumping volume, downforce, head opening torque, rebound speed, water intake indicators.

The dispenser is divided into two types: tie type and screw type. From the function, it is divided into spray, foundation cream, lotion pump, aerosol valve, vacuum bottle. The size of the pump head is determined by the diameter of the matching bottle. The spray size is 12.5mm-24mm, and the water output is 0.1ml/time-0.2ml/time. It is generally used on the packaging of perfume, gel water and other products. The length can be determined according to the height of the bottle.

The size range of the foam pump head is 16ml to 38ml, and the water output is 0.28ml/time – 3.1ml/time. It is generally used in creams and washing products. Special dispensers such as foam pump heads and hand-held nozzles, the non-inflated hand pump head, does not require gas to create foam, and can be used to produce quantitative high quality foam with a light press. It is usually equipped with a special bottle. Hand-held sprinklers are commonly used on products such as cleaners. The composition of the dispenser is relatively complicated, generally including: dust cover, hoe, mast, gasket, piston, spring, valve, bottle cap, pump body, straw, valve ball (with steel ball, glass ball). The cap and dust cover can be made colored, electroplated, and can be made of an electric aluminum ring.

The vacuum bottle is usually cylindrical, the specification is 15ml-50ml, and the individual has 100ml. The overall capacity is small. It relies on the principle of atmospheric pressure to avoid contamination of the cosmetics during use. The vacuum bottle has anodized aluminum, plastic plating and colored plastic. The price is more expensive than other common containers, and the general order quantity is not high. The dispenser customers rarely open their own molds, and the molds they need are more and more expensive.

Click Foam Pump Suppliers to learn about more information

Silk Screening for Foam Pump Bottles

Silk screening for a Foam Pump(KEXON) bottles not only enhances the appeal of the bottles but also allows you to use vibrant colors and designs for your labels. All kinds of plastic and glass bottles can be silk screened with text and designs; even closures can be silk screened if required. Whether you want your current bottles with a new design or are launching something new, you can increase sales by presenting an attractive foam pump bottle. In fact, it is often a good idea to help sluggish or stagnant sales by new designs in shapes and colors as potential customers’ eyes often simply disregard what has been seen many times before.

Art via silk screening for foam pump bottles

Silk screening looks good, but the technique has other benefits as well, among them being: Increase label durability,Print directly on bottles, Have better bottling line efficiency,Add value to the products,Use between one and six colors,Get 360° wrap around labels offering more space, Command a premium price because of the way it looks, Higher level of scratch resistance, Color fast – will not fade,Won’t scuff or scratch, No problems with labels coming off, You can do large or small runs.

With the market flooded with products, you need that competitive edge that will make your product stand out and increase sales. When you opt for silk screening for bottles, using shapes and colors depending on your target market, you have already taken the first step towards attracting the consumer. Whether you make beauty, household, cosmetic or other product, we can help you improve your sales.

Click Foam Pump Manufacturers to learn about more information

How To Trick Out Your Foam Pump Hand Soap Dispenser

One of my least favorite chores in the kitchen has always been re-filling the built-in Foam Pump(KEXON) hand soap dispenser at my kitchen sink. Through years of extensive research in to this matter, I’ve discovered that I’m not alone. Approximately 57.3% of soap dispensers in the KEXON metro area remain unfilled; sitting next to the empty Foam Pump soap dispensers, I often find unsightly store-bought bottles of hand soap.

I have many reasons to not refill my soap dispenser.For one, they’re difficult to access. Mine is so tough to get at that I need to lay on my back under the kitchen sink just to unscrew it.They’re difficult to fill. Why are the openings so small?!What used to happen to me every time I would try to fill my dispenser. I’ve tried a funnel, but this doesn’t work either – the soap is too thick.

Another problem is getting the dispenser screwed back in place under the counter – it’s very difficult to see under there. I actually installed a fluorescent light inside my kitchen cabinet to help with this chore.Finally, this is a grueling task that demands action about once a month. If I only had to do it once a year, that would be fine, but we wash our hands in the kitchen more than anywhere else in the house, and the tiny container doesn’t hold much soap.

Click Foam Pump Manufacturers to learn about more information